Lepak za drvo
Lepak za drvo
Jedna možda interesantna tema. Koji lepak za drvo koristite, i koji vam se najbolje pokazao?
Zadnji put sam ga kupovao kod BeoIcle, ne secam se cene.velja wrote:gde kupujes titbond i po kojoj ceni?
Dragoslava Srejovića 1b, Beograd
Tel./Fax: 011/ 754-862, 2762-226, 2764-050
http://www.beoicla.co.yu/html_s/onama.html
A video sam ga skoro jos u nekoj radnji samo kad bih sad mogao da se setim...
Juce sam na sajmu video da firma FURNEX takodje prodaje titebond a cena je za titebond III 300 i nesto dinara za 0.5l. taj je u klasi D4. Ja sam do sada koristio kleberit D3 mislim da je 313 ili 330 tako nesto, glavno vodootporan. Takodje sam koristio malo i henkel-ov MOMENT express za stvari koje su trebale brzo da se zavepe. On je zut kad se osusi
VELJA
VELJA
Kako kazu nasi stari: "Bolje znati mnogo i cesto, nego ne znati nista, povremeno nikad, kojekude..."
Evo, odguglao sam i nasao tu klasifikaciju:
Therefore a very important test, for wood bonding is the EN 204 standard, " Classification of non structural wood adhesives ", which allows to classify wood adhesives in 4 classes:
* D1 adhesives require only a dry resistance of 10 MPa minimum, this corresponds to dry conditions such as interior furniture or decoration,
* D2 adhesives should withstand a 3 hours immersion in water at 20°C, followed by drying and the test requires a minimum resistance of 8 MPa after drying. These requirements corresponds to occasional exposure in kitchens and bathrooms.
* D3 adhesives must withstand several cycles including several 4 days immersion in water at 20°C and then drying, and the requirements are: initial resistance 10 MPa, wet resistance 2 MPa, and after drying 8 MPa.
These requirements correspond to outside windows and doors, kitchen and bathrooms furniture. Vinyl adhesives crosslinked with hardeners and many UF belong to class D3.
* D4 adhesives should withstand several cycles including several immersion of 6 hours in boiling water, and then drying. The minimum requirements are: initial resistance 10 MPa, wet 4 MPa and after drying 8 MPa.
Ima na tom site-u dosta lep tekst uopste o lepku za drvo (malkice je strucan, al nije preterano). Nezgodan je da se ubaci direktno u poruku (ima dosta slikica), a ne vidim da moze da se prikaci fajl za poruku (recimo .pdf).
Koga interesuje adresa je:
http://www.specialchem4adhesives.com/re ... spx?id=952
i drugi deo na adresi
http://www.specialchem4adhesives.com/re ... px?id=1024
Sajt trazi registraciju (besplatna je al samo sto ne pitaju za broj cipela).
Therefore a very important test, for wood bonding is the EN 204 standard, " Classification of non structural wood adhesives ", which allows to classify wood adhesives in 4 classes:
* D1 adhesives require only a dry resistance of 10 MPa minimum, this corresponds to dry conditions such as interior furniture or decoration,
* D2 adhesives should withstand a 3 hours immersion in water at 20°C, followed by drying and the test requires a minimum resistance of 8 MPa after drying. These requirements corresponds to occasional exposure in kitchens and bathrooms.
* D3 adhesives must withstand several cycles including several 4 days immersion in water at 20°C and then drying, and the requirements are: initial resistance 10 MPa, wet resistance 2 MPa, and after drying 8 MPa.
These requirements correspond to outside windows and doors, kitchen and bathrooms furniture. Vinyl adhesives crosslinked with hardeners and many UF belong to class D3.
* D4 adhesives should withstand several cycles including several immersion of 6 hours in boiling water, and then drying. The minimum requirements are: initial resistance 10 MPa, wet 4 MPa and after drying 8 MPa.
Ima na tom site-u dosta lep tekst uopste o lepku za drvo (malkice je strucan, al nije preterano). Nezgodan je da se ubaci direktno u poruku (ima dosta slikica), a ne vidim da moze da se prikaci fajl za poruku (recimo .pdf).
Koga interesuje adresa je:
http://www.specialchem4adhesives.com/re ... spx?id=952
i drugi deo na adresi
http://www.specialchem4adhesives.com/re ... px?id=1024
Sajt trazi registraciju (besplatna je al samo sto ne pitaju za broj cipela).
Sad videh ima ustvari devet delova, samo se malo drugacije zovu. Koga bude interesovalo neka trazi termin Woodworking pa ce tako naci svih devet.
Ako se pojavi mogucnost da se prikaci fajl uz poruku, mogu da posaljem komplet .pfd (mislim da je dosta interesantno iako je vise na industrijskom nego na radionickom nivou).
Ako se pojavi mogucnost da se prikaci fajl uz poruku, mogu da posaljem komplet .pfd (mislim da je dosta interesantno iako je vise na industrijskom nego na radionickom nivou).
Cini mi se da je prosle godine sajam bio bolji, bar sto se tice repromaterijala. Nasao sam par firmi koje prodaju furnire, sto me je unapred interesovalo, europanel team ima sper plocu za savijanje (moze da se savije u cilindar, na primer) i jos neke stvari koje su meni licno bile interesantne. Sto se namestaja tice, uglavnom sam gledao ideje i trendove.
Kako kazu nasi stari: "Bolje znati mnogo i cesto, nego ne znati nista, povremeno nikad, kojekude..."
Evo jos malo na temu lepkova za drvo:
http://www.formica.co.uk/publish/site/e ... sives.html
pozdrav
bogi
http://www.formica.co.uk/publish/site/e ... sives.html
pozdrav
bogi